Search found 11 matches

by bdtopp
Wed Feb 05, 2014 1:04 am
Forum: EIS Sensors
Topic: Oil Temp Not Working
Replies: 2
Views: 6971

Re: Oil Temp Not Working

I did. There was an issue with the EIS. I sent it back to GRT for repair and it's working great. I don't have any details on what the issue was with the EIS box. If you have tried all the test I did mentioned previously in the post, you may want to talk to GRT about sending back. Hope this helps...
by bdtopp
Tue Oct 29, 2013 9:25 pm
Forum: Show Us Your Panel
Topic: F1 Rocket with Dual Hx Displays
Replies: 1
Views: 6449

F1 Rocket with Dual Hx Displays

P1040022.JPG
P1040022.JPG (497.49 KiB) Viewed 6449 times
by bdtopp
Sun Jul 07, 2013 1:38 am
Forum: Horizon HX
Topic: General Setup - Flight ID & Address
Replies: 2
Views: 4470

Re: General Setup - Flight ID & Address

Thanks!!
by bdtopp
Sun Jul 07, 2013 12:29 am
Forum: Horizon HX
Topic: General Setup - Flight ID & Address
Replies: 2
Views: 4470

General Setup - Flight ID & Address

I noticed in the General Setup entries for Flight ID & Address. I could not find anything in the manual for documentation on these settings. Is the Flight ID the N-number of aircraft, and, Address the Mode S code assigned to airplane (hex on octal?) for ADS-B?

Thanks.
by bdtopp
Sun Jul 07, 2013 12:04 am
Forum: EIS Sensors
Topic: Fuel Pressure Not Working
Replies: 0
Views: 3594

Fuel Pressure Not Working

I ran the engine for the first time and discovered that I am not getting any indication of fuel pressure on the EIS or HX EFISs. I have the 80psi VDO type sensor. This was confirmed by GRT a few months back when I gave them the part number. The fuel pressure reading is -0.4 psi with the engine off, ...
by bdtopp
Sat Jul 06, 2013 11:52 pm
Forum: EIS Sensors
Topic: Oil Temp Not Working
Replies: 2
Views: 6971

Oil Temp Not Working

I ran my engine for the first time and discovered that the Oil Temp was not working on the EIS or HX EFIS's. Here is what I have done thus far in an attempt to figure out the problem. 1. I have verified that there is continuity from EIS D-sub connector Pin 15 to the Oil Temp Sensor. 2. I have a good...
by bdtopp
Sun May 19, 2013 1:26 am
Forum: Horizon HX
Topic: Engine Performance Table Setup
Replies: 3
Views: 5366

Re: Engine Performance Table Setup

Thanks Jeff...
by bdtopp
Fri May 17, 2013 1:50 am
Forum: ADS-B/Weather/Traffic
Topic: NavWorx ADS-B Setup with Hx
Replies: 6
Views: 9972

Re: NavWorx ADS-B Setup with Hx

thanks
by bdtopp
Fri May 17, 2013 1:46 am
Forum: Horizon HX
Topic: Engine Performance Table Setup
Replies: 3
Views: 5366

Engine Performance Table Setup

I am working on the engine performance table setup (Hx Setup and Config Guide pg 6-6) so the EFIS can calculate % Power. I am skeptical that I created the table correctly. Does anyone have a performance table for a IO540 D model that works well they would share?

Thanks..
by bdtopp
Mon May 13, 2013 2:29 am
Forum: ADS-B/Weather/Traffic
Topic: NavWorx ADS-B Setup with Hx
Replies: 6
Views: 9972

NavWorx ADS-B Setup with Hx

I have a NavWorx ADS-B and a dual display Hx system. The NavWorx RS232 Display Serial Data Input (Pin 24), and, the RS232 Display Serial Data Output (Pin 5) are connected to display unit #1 Serial 7 In and Serial 7 Out. When I am in the General Setup for Display Unit #1, what baud rate and value sho...