Search found 51 matches
- Thu Apr 04, 2013 12:41 pm
- Forum: EIS Sensors
- Topic: Oil temperature sensor failure
- Replies: 2
- Views: 8251
Re: Oil temperature sensor failure
Pascal It could be an indication of either one. if there is a short to ground or if there is an intermittent open, they both can cause erratic indications. check out your wiring, for continuity and for short to ground. you dont find any issues then it may be the sender. If it happens more and more f...
- Tue Apr 02, 2013 12:34 pm
- Forum: EIS Sensors
- Topic: EGT probes too small
- Replies: 1
- Views: 5194
Re: EGT probes too small
The flange on the GRT Probe is large enough to cover the hole from the othe probes, so you can leave it if you would like to. Other wise the other option is to have the pipes welded and then drill a new hole the right size.
- Thu Mar 28, 2013 8:21 pm
- Forum: EIS Sensors
- Topic: EIS Tach fluctuation issues
- Replies: 3
- Views: 11955
Re: EIS Tach fluctuation issues
Scott
If you are seeing the fluctuations in the RPM during run up RPM it is likely an interference. Try adding a 10K ohm 1/2watt 5% resistor in the line. this may drop the signal to the point you would need to use the high sensitivity setting on the EIS. it may clear things up.
If you are seeing the fluctuations in the RPM during run up RPM it is likely an interference. Try adding a 10K ohm 1/2watt 5% resistor in the line. this may drop the signal to the point you would need to use the high sensitivity setting on the EIS. it may clear things up.
- Tue Mar 26, 2013 2:56 pm
- Forum: Autopilot
- Topic: Auto Pilot Software update 13 to 14
- Replies: 1
- Views: 7328
Re: Software update
The software change for the servos was only to deal with a hardware chage we had to make for the circuit boards. There is no functional changes to the software that need to be dealt with.
- Tue Mar 26, 2013 2:53 pm
- Forum: EIS Installation
- Topic: EIS audio out
- Replies: 9
- Views: 32857
Re: EIS audio out
Jeff If you use the EIS audio output it will only give you EIS warned limit breaks. which is what you want I think. If you use the EFIS audio output it will warn all alarms engine and flight related. If you are blind mounting the EIS you wont have the ability to acknowledge the warning and the tone ...
- Mon Mar 25, 2013 8:58 pm
- Forum: Autopilot
- Topic: Pitch servo: Is this ok?
- Replies: 4
- Views: 17304
Re: Pitch servo: Is this ok?
Tim
This is normal, the pitch servo has a trim sensing system in it that mounts the motor to the servo and makes it look like it "floats". It does allow some movement of the motor but that needs to be there to allow the trim sensing to work.
This is normal, the pitch servo has a trim sensing system in it that mounts the motor to the servo and makes it look like it "floats". It does allow some movement of the motor but that needs to be there to allow the trim sensing to work.
- Thu Mar 21, 2013 4:18 pm
- Forum: EIS Programming
- Topic: Flashing (blinking ) fuel quantity
- Replies: 1
- Views: 7103
Re: Flashing (blinking ) fuel quantity
Bob
If it is blinking on the eis or efis then the number that is being displayed is outside of the parameters that you have set. check that your min and max for that aux are set where they need to be..
Ben
If it is blinking on the eis or efis then the number that is being displayed is outside of the parameters that you have set. check that your min and max for that aux are set where they need to be..
Ben
- Wed Mar 20, 2013 2:32 pm
- Forum: Show Us Your Panel
- Topic: N97AP HX/HS in an RV8A
- Replies: 2
- Views: 10056
Re: N97AP HX/HS in an RV8A
Clean and neat. I like that one, might need another screen on the right so you could have PFD, MAP, and ENG pages all at the same time.
Ben
Ben
- Wed Mar 20, 2013 2:27 pm
- Forum: EIS Programming
- Topic: Converting from Electronic Ignition to Mags
- Replies: 2
- Views: 10486
Re: Converting from Electronic Ignition to Mags
The last page of the EIS manual on the website details adding the needed resistor to connect to the P-lead connection on the mag.
http://grtavionics.com/documents/4000-6 ... igures.pdf
Ben
http://grtavionics.com/documents/4000-6 ... igures.pdf
Ben
- Wed Mar 13, 2013 6:34 pm
- Forum: Product Feature Requests
- Topic: Fuel flow on bottom of PDF page
- Replies: 7
- Views: 16706
Re: Fuel flow
If you set the FF as a dial number 1 or 2 it will show on the right side of the bottom engine bar.
Ben
Ben