Search found 60 matches

by Kahuna
Sat Jun 16, 2018 4:39 pm
Forum: Horizon HXr
Topic: "Roll Trim Required"... Why?
Replies: 2
Views: 3377

Re: "Roll Trim Required"... Why?

Thanks Jeff. The update fixed the problem.
by Kahuna
Fri Jun 15, 2018 11:21 am
Forum: Horizon HXr
Topic: "Roll Trim Required"... Why?
Replies: 2
Views: 3377

"Roll Trim Required"... Why?

HXr/Mini. When running AP off the Mini, I get constant errors on the HXr "Roll trim required". Disconnecting the AP and the planes flies level with no trim required. How do I make it stop? I do not get the errors on running the AP from the HXr. All software is up to date and I started gett...
by Kahuna
Tue Jan 14, 2014 12:51 am
Forum: Horizon HX
Topic: Geo Referenced Approach Charts
Replies: 1
Views: 3765

Re: Geo Referenced Approach Charts

shhhhh. Mums the word.
by Kahuna
Fri Nov 15, 2013 1:41 pm
Forum: EIS Sensors
Topic: Princeton Capacitive fuel probe programming / calibration
Replies: 11
Views: 36155

Re: Princeton Capacitive fuel probe programming / calibratio

I don't believe the info that Kahuna posted about setting the EIS scale to read tenths of a gallon is in any capacitive probe documentation but I think it should be. Kahuna, that works on the EIS 2000? Does it depend on the software version that's installed? I am not sure about that. I have the 6cy...
by Kahuna
Mon Oct 28, 2013 8:48 pm
Forum: EIS Sensors
Topic: Wire to amp meter pulled out
Replies: 2
Views: 6296

Re: Wire to amp meter pulled out

hmmm. Sounds like a guess. That fitting can go one way or another way 180 out.
by Kahuna
Sat Oct 26, 2013 6:09 pm
Forum: EIS Sensors
Topic: Wire to amp meter pulled out
Replies: 2
Views: 6296

Wire to amp meter pulled out

For what ever reason my wires pulled out of the amp meter. Pic attached. I have a green blue and black wire. Ill solder back in place.
If the pins in the picture are 1,2 & 3 top to bottom, which wire goes where?
ampwires.jpg
ampwires.jpg (130.24 KiB) Viewed 6296 times
by Kahuna
Tue Jul 16, 2013 9:26 am
Forum: Horizon HXr
Topic: Long AHARS boot wait times
Replies: 5
Views: 10484

Re: Long AHARS boot wait times

Good to know Jeff. THanks. That helps a lot.
by Kahuna
Wed Jul 10, 2013 3:58 pm
Forum: EIS Installation
Topic: EIS 400 and P-Mag compatibility
Replies: 1
Views: 4735

Re: EIS 400 and P-Mag compatibility

Older unit you did have to cut I think it was a cap lead off on the board in order to wire to an EI. Newer units did not have this.
Im sure GRT will chime in with the details.
by Kahuna
Mon Jul 08, 2013 9:20 pm
Forum: Horizon HXr
Topic: Long AHARS boot wait times
Replies: 5
Views: 10484

Re: Long AHARS boot wait times

dmaib wrote:I see this occasionally, but I would estimate about 75% of the time it boots up in about 40 seconds.
Dave is your engine running during this boot period?
by Kahuna
Mon Jul 08, 2013 3:23 am
Forum: Horizon HXr
Topic: Long AHARS boot wait times
Replies: 5
Views: 10484

Long AHARS boot wait times

All our team is seeing this same behavior. On boot, get to PDF and there is a count down from ~40 sec on ahars. Then it resets to ~2:30 seconds and we essentially have a 3 min sit and wait period for the ahars to stabilize. This may not seem like a long time, but it is. How do we get this number to ...